DNP COLOR VIEWER CCV31F,CCV31F/G维修
价 格：询价
产 地：更新时间：2021-01-19 15:38
品 牌：型 号：
状 态：正常点击量：2457
400-006-7520
联系我时，请说明是在上海非利加实业有限公司上看到的，谢谢！
联 系 人：
上海非利加实业有限公司
电 话：
400-006-7520
传 真：
400-006-7520
配送方式：
上海自提或三方快递
联系我时请说在上海非利加实业有限公司上看到的,谢谢！
| |
 |
| Light source: | DNP Standard color Viewer lamp
（Four 10W dedicated fluorescent tubes are used） | | Power supply: | AC100V 50, 60Hz | | Lighting method: | High Frequency lighting method 20KHz | | Color rendering: | Over 90% rendering evaluation-point for each color | | Color temperature: | （Measured by Minolta CL-200） | | Operating temperature: | 10～40℃ | | Operating humidity: | Below 80%（avoid dew） | | Major diameter dimension: | 375W×365H×165D m/m | | Luminance plane dimension: | 250W×190H m/m | | Color chart dimension: | 320W×290H m/m | | Power consumption: | 80W | | Weight: | 6.5kg/7.5kg | | |  | CCV-31F
CCV-51F | |  | CCV-31F/G
CCV-51F/G | | | |
|
| ●The Luminance plane characteristics: according to the types of self-contained fluorescent lamp |
|
| Product Type | Luminance Color Temperature | Lamp | Color Temperature | Luminance | Color matching shift | Weight | | CCV-31F | Fixed | FL10WW-DLB | 3100K±300 | Over 1300cd/m2 | Within 10% | 6.5kg | | CCV-51F | Fixed | FL10D-EDL-56K | 5100K±300 | Over 1400cd/m2 | Within 10% | 6.5kg | | CCV-31F/G | Volume adjustable | FL-10WW-DLB | 3100K±300 | Over 850～1300cd/m2 | Within 10% | 7.5kg | | CCV-51F/G | Volume adjustable | FL10D-EDL-56K | 5100K±300 | Over 850～1400cd/m2 | Within 10% | 7.5kg | |
|
＊The color temperature if Luminance. Color Temperature Conversion Type viewer ranges over 50k according to the change of the Luminance.
＊The specification may change without notice |
|
| |
|
| 【1】 | Before using the product: | | | | Power supply | | AC 100V, 50/60Hz shared | | Light source | | 10W DNP Standard color Viewer Lamp （4） | | Power consumption | | 80W | |
|
| 【2】 | Using the DNP Standard color Viewer | | | | （1） | Plug the power cable of the product into AC100V | | | | | 【Precautions】 | Do not connect any power supply other than AC100V
If the other power supply connected by accident, the inverter inside will burned out | | | | （2） | Turn on the power switch | | | （3） | Lamp lights: the lamp light will stabilised after 15 to 20 minutes at the room temperature（20℃） | | | （4） | If the lamp does not lit, call for Service Office for the confirmation as described on other documents. | | | （5） | To suspend snaking of the lamp, press power switch 3 to 4 times [as ON/OFF]. | |
|
| 【3】 | If the light does not lit | | | | Call for Service Office to confirm the following: | | | （1） | AC 100V supplied to the wall socket. | | | （2） | Plug the product into the wall socket. | | | （3） | Turn the power supply switch of the product ON | | | | | | | | | Still the lamp does not lit: Consider the following: | | | | | | | | | （1） | Two of the viewer lamps lit simultaneously, one of the fuses of the inverters has blowouts. | | | （2） | Four of the viewer lamps does not light means that each of the fuses of the two inverters has blowouts. | | | | | 【Precautions】 | The above occurs if the applied power supply is not AC 100V.
Fuse bum out cause internal burnout of inverter. The burned inverter needs to replace. | | |
|
| 【4】 | How to replace the lamp ａnd keep it clean | | | | Place the Viewer on the flat table, ａnd plug out the power supply cable from the wall socket.
Remove the used device in the following order: | | | （1） | Unfasten the two of grub screws on the top frame. | | | （2） | To remove the top frame from the main unit;
Holding 50 to 60 mm the grub screw of the top frame ａnd press it forward. | | | （3） | Remove the glass plate ａnd acrylic plate. | | | | | 【Precaution】 | Glass plate easily breaks ａnd may hurt your hands ａnd fingers.
Handle the edge of the plate with care not to scratch. | | | | | ◆Replacing the lamps: | | | （1） | When the lamps used over 2,000 hours or one year, it needs to replace. | | | （2） | Remove the Lamp Tubes: Hold the edge of the Lamp Tubes, ａnd turn it 90 degree. | | | | ◆Cleaning the device: | | | （1） | Impregnate alcohol to gauze then apply it onto the surface of the reflection plate / acrylic plate / glass surface to remove the dirt. | | | （2） | Clean the device once in six months to one year to keep quality of the Color Temperature ａnd Luminance. | |
|
| 【5】 | Other Precautions | | | | Handling the viewer needs the following precautions because it contains the parts using glass. | | | （1） | Do not add strong impact on the viewer | | | （2） | Do not put any heavy items on the surface of the viewer | |
沪公网安备31011502016460号
